Written by Jay Alison TDL
01/16/2017 Dog Bark Collar, Barking Dog Collar
How to Find a Broken Dog Fence wire. If the Dog Fence Transmitter is beeping, It means you have a broken wire somewhere around the invisible dog fence perimeter. You will need to locate the break in the wire and fix it. This review shows a series of steps to help you locate the break in the wire and perform the repair.
1. How do I know If my Dog Fence Wire is broken?
2. Short Loop Wire Test - Test for a break with the Dog Fence Transmitter
3. Physical and Visual Test to find the Broken Wire
4. Test the buried wire leading to the fence - ‘Return Short Circuit Loop’
5. Bypassing any Underground and Buried Dog Fence Wire - A Bridge
6. How to Fix the Broken Dog Fence Wire
Do you need to buy more dog fence wire to replace any old and damaged wire?
We get a lot of calls from people asking us “How do i find a break in my Dog Fence Wire?” The answer can either be a long or a short journey. Some people get lucky and find it straight away, others usually find it in the last place they look… and that’s called Murphy's Law.
We did a short video on ‘Finding a break in dog fence wire’
So let's go through the steps and find out how to find a break in the dog fence wire. First, we need to establish that the break is in the wire, and not the transmitter. Then, we can start the process of elimination and find where the break in the wire could be.
But before anything else… Try to think of any recent events where a gardener may have been doing some digging. Then, you can just go to the area where they were working and inspect the wire there. If you’re lucky and assuming it’s the only break in the wire, skip straight to step 6. If not, keep reading.
The first thing to find out is if the system is broken... Is it a broken wire or a broken transmitter? Usually if the transmitter is beeping it does mean a broken wire. (In fact i consider a beeping transmitter to be a sign of a healthy transmitter.)
You could have a system that doesn't have any lightning and surge protection on it and when lightning strikes, there’s a spike of energy that goes to the transmitter that can damage the circuit board.
Click here to see how the Dog Fence Transmitter works.
So, quite simply - if your transmitter is beeping - it is a good sign… it is more than likely a break in the wire. If so, follow the steps below.
A short loop test will stop the transmitter beeping and test it as well - if it stops beeping there will be a break somewhere or a bad connection.
There is a simple way to do this. Just follow the steps below:
Basically a short loop disregards the rest of the property and ‘Arcs’ or ‘Bridges’ the radio signal straight back to the transmitter to close the loop. (You should not get Zapped as this is a radio signal)
a. Check your transmitter and look for the two wires coming from the main connection to the transmitter - find where they join at the transmitter.
b. Disconnect both wires from the transmitter. (If you have an external surge protector you can just do the short loop there.)
c. Get a length of test wire or a paper clip to put inside these two contact points where the wires were connected.
d. Connect the test wire to form a loop.
e. If the beeping stops, then we’ve established that it is indeed a wire break and your transmitter is working properly.
Another simple solution to test if you have a dog fence wire break is to use an ohmmeter and check the continuity on the disconnected wires. If there is zero resistance on the wires then you have a wire break.
Note… this may give you a false reading as if it is a bad connection it may let the test through - but not the radio signal - remember the is radio frequency not electricity you are dealing with.
Back to basics… Now that you are sure that there is break in your Electronic Dog Fence Wire, you then need to find where it is. The simplest step is to do a physical and visual check of your dog fence wire.
The usual reason for a broken dog fence wire is physical damage, i.e. gardening, weed whacking, edging, and pesky rodents. If you know where you may have had some work done, you can go straight to that location and start your check.
If you don’t know where to start, you can follow these steps to find out:
a. Note that you can only use the physical check to find a broken wire in your dog fence if the wires are not buried underground. If they are, it will be tackled in the next section.
b. Begin your visual check at the transmitter, where you first see the wire above ground.
c. Walk around the dog fence wire, give it a tug, see if it has tension or if it is loose.
d. Follow the wire around your property and look for areas where they may have been twisted or chopped. (It may be an internal break)
e. Walk around the dog fence wire system and pay attention to areas where there is heavy traffic like pathways, driveways and sidewalks. These are also the most common places to find a broken wire.
Note… you may have more than one break… so if you make a temporary repair - keep going.
Now, if there is no wire break during your physical and visual check up then there’s a possibility that the break is underground.
In order to check the wire break without digging up all of the buried wire, you’ll need to test the circuit between the fence and the transmitter (the twin pair running to to fence)
You just need to cut them at the fence and join them together to send the radio signal back to the transmitter. If it stops beeping, there's no break underground. Rejoin them and carry-on.
Go to the driveway where you have the wire underground.
In this test, you need to have enough wire to go across the driveway for a test bridge. You can use this test on underground dog fence wire such as the driveway - gateways and around gardens etc.
Simply cut the wire on both sides of the driveway and Bridge across with the new wire.
Some people have spliced into the wire - the signal will take the shortest route home so it will disregard the buried wire.
If the beeping stops, the break is in the wire buried under the driveway. So just run a new electronic dog fence wire underground.
If the beeping continues, then you know there's no break on the wire underground the driveway. (But leave that wire there… you may have 2 breaks)
Then, you go to the next phase, next gateway and do bridging again until you find where the wire break is.
Now that you know where your wire break is, the final step is to repair and fix the broken dog fence wire in a way that is weatherproof and secure. Best way is keep it simple -
a. Strip the wire
b. Twist the ends together - ‘butterfly twist’
c. Tie a knot in it
d. Wrap in electrical tape
e. Fold it over a couple of times
f. Wrap it again
g. Leave extra slack around the property for joins if you get a break in the wire.
If the wire break is underground, you’ll need to dig up the wire first to expose the broken wire, or simply leave it there and run new wire.
If the wire is too short to re-join, you can use your test wire to make the connection. Once you are sure that the dog fence wire is operating correctly, return it back to the area where it’s supposed to be.
One of the best things you can do to prevent wire breaks is to purchase a strong electronic dog fence wire with polyethylene coating so that even if you’re going to hit it with a shovel, it won’t break.
You can put the wire inside some poly pipe to protect it from Whipper Snippers.
If you want an easier solution to fix the wire break, you can email us, call us or chat with us so we can do the finding and fixing for you. We can also discuss on Electronic Dog Fence wire that will give you long-lasting results.
Here for you and your dog, Colin Seal